Luminex xPONENT 4.2 for FLEXMAP 3D Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Logiciel Luminex xPONENT 4.2 for FLEXMAP 3D. Luminex xPONENT 4.2 for FLEXMAP 3D User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 20
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Quick Guide
xPONENfor FLEXMAP 3 Software
Version 4.2
Vue de la page 0
1 2 3 4 5 6 ... 19 20

Résumé du contenu

Page 1 - Version 4.2

Quick GuidexPONENT® for FLEXMAP 3D® SoftwareVersion 4.2

Page 2

7. Type a name for the plate in the Plate Name box, or select a saved plate from the PlateName list.NOTE: If a saved plate is selected the results of

Page 3 - Table of Contents

Revive After Storage RoutineNOTE: The Revive After Storage routine is necessary when the systemhas been idle for more than a week.After you have adjus

Page 4 - for FLEXMAP 3D

7. Load wells with at least five drops of the Calibration, Verification, and Fluidics beads, asindicated on the plate image and in the kit insert inst

Page 5 - Start-up Indicators

4. Vortex the xMAP calibrator, verification, and fluidics containers for 30 seconds to ensurehomogeneity. Do not dilute xMAP calibrator, verification,

Page 6 - Software Overview

To run, print, and/or save a report:1. Open the Results page.2. Click the Reports tab.3. In the Report drop-down list, select the report that you want

Page 7 - System Monitor

You can create each quantitative, qualitative, and allele call protocols using one productcomposed of a definable number of standards and controls.The

Page 8 - Initial Startup

6. Select Fit of all Standards or Mean of Replicates.7. Select Analyze results while acquiring samples if you want to view real-time analysis.8. Click

Page 9

11. Add standards, controls, unknowns, and maintenance steps to the plate layout.12. Click Save to save the protocol. Creating a KitTo create a kit:1.

Page 10

Create a BatchThere are three batch creation options:• Create a New Batch from an Existing Protocol (uses a protocol; described in thissection).• Crea

Page 11 - Initialize the System

2. Select the Current Batch or Saved Batches tab.3. If you want to open a saved batch, highlight the batch and click Open. Shut Down the InstrumentRun

Page 12

© Luminex Corporation, 2012. All rights reserved. No part of this publication may bereproduced, transmitted, transcribed, or translated into any langu

Page 13 - Run, Save, and Print Reports

By Phone Inside the U.S. and CanadaContact Luminex Technical support at:• Toll Free: 1-877-785-BEAD (-2323)• Fax: 512-219-5114By Phone Outside the U.S

Page 14 - Create a Protocol

Table of ContentsStartingxPONENT®...

Page 15

xPONENT™ for FLEXMAP 3D®iv

Page 16

StartingxPONENT®• On the PC desktop, click the Luminex® xPONENT® icon, or click Start > All Programs >Luminex > xPONENT > Luminex xPONENT.

Page 17 - Creating a Kit

Software OverviewxPONENT® software is organized into a series of pages. As you click each page, applicabletabs open on the left-hand side of the windo

Page 18 - View Batches

Results - Analyze previously acquired batches; view current and saved reportsProtocols - Displays protocols, Stds & Ctrls, and Lot information.Mai

Page 19 - Shut Down the Instrument

System Status Button - This button has two functions: When clicked, it opens the systemlog. It also displays the current status of the system. If ther

Page 20

Adjusting the Sample Probe HeightAdjust the sample probe height to ensure that the probe drops far enough into the well toacquire sample.NOTE: Ensure

Commentaires sur ces manuels

Pas de commentaire