Luminex IS Version 2.3 (IVD) Manuel d'utilisateur Page 56
- Page / 116
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Luminex IS Software Manual for Version 2.3- For In Vitro Diagnostic Use xMAP Technology
46
12. Click CAL2, then click OK. Wait until CAL2 completes.
The Device Status section in the status bar changes from “Running”
to “Standby” and the Diagnostics tab turns red. The System Monitor
on the Diagnostics tab displays the date and time in green if CAL1
and CAL2 are successful.
The Diagnostics tab turns red if all substances (CAL or CON) have
not been run and under the following conditions:
• the first time the software is opened
• the first time a system is calibrated
• a new database is installed
• an old database is restored
• a CAL or CON fails.
You must run system controls following calibration. Continue with
the following “Run System xMAP Controls” section.
Run System xMAP
Controls
Run System xMAP controls to verify calibration. Dispense the
Control microspheres into the microtiter plate at the same time that
you dispense the Calibration microspheres. See “Run System xMAP
Calibrators” on page 44.
To verify system calibration with controls:
1. In the Maintenance tab, click New CON Targ. The Update
CON Target Information dialog box opens. See Figure 26.
2. Enter the CON1 lot number, expiration date, and the values listed
from the COQ included with your system controls into the
CON1 entry boxes. If you are using a previously entered lot,
select it from the drop-down menu in the Current CON 1 group
box or click Import to import the information. See page 48 for
more details on importing a lot.
3. Repeat step 2 for the CON2 lot information.
- Luminex® IS 1
- Software Manual For 1
- Version 2.3 1
- Bergerweg 18 2
- 6085 AT Horn 2
- The Netherlands 2
- EULA PN: 89-30000-00-070 6
- Contents 7
- PN 89-00002-00-254 Rev. B ix 9
- Luminex 2.3 Software 11
- PN 89-00002-00-254 Rev. B 3 13
- PN 89-00002-00-254 Rev. B 5 15
- 3. Command List 16
- Figure 4 Run Batch Tab 16
- PN 89-00002-00-254 Rev. B 7 17
- Figure 7 Maintenance Tab 18
- PN 89-00002-00-254 Rev. B 9 19
- PN 89-00002-00-254 Rev. B 11 21
- Acquisition Detail 22
- PN 89-00002-00-254 Rev. B 13 23
- Figure 15 System Status Bar 27
- Diagnostics tab 28
- Disconnected 29
- Secondary 30
- PN 89-00002-00-254 Rev. B 21 31
- PN 89-00002-00-254 Rev. B 23 33
- Figure 19 Competitive Assay 36
- Replicate 37
- Averaging 37
- PN 89-00002-00-254 Rev. B 29 39
- PN 89-00002-00-254 Rev. B 31 41
- PN 89-00002-00-254 Rev. B 33 43
- PN 89-00002-00-254 Rev. B 35 45
- Define General 47
- Tab Information 47
- Define Company 48
- Information Tab 48
- Define Data Export 49
- Setting up the Favorites 50
- Startup Procedures 51
- Set Luminex XYP 53
- Instrument Heater 53
- Temperature 53
- Run System xMAP 54
- Calibrators 54
- PN 89-00002-00-254 Rev. B 45 55
- Controls 56
- PN 89-00002-00-254 Rev. B 47 57
- PN 89-00002-00-254 Rev. B 49 59
- C:\Program 59
- PN 89-00002-00-254 Rev. B 51 61
- PN 89-00002-00-254 Rev. B 53 63
- The Open Batch 64
- Create a Multi 65
- Open a Multi 66
- To open a multi-batch: 66
- Process Multiple 67
- PN 89-00002-00-254 Rev. B 59 69
- To edit a patient list: 70
- Assign Sample 71
- Dilution Factors 71
- PN 89-00002-00-254 Rev. B 63 73
- Edit Lot 74
- Information on an 74
- Unused Template 74
- Information on a 75
- Used Template 75
- Analyzing Batches and 77
- Multi-Batches 77
- Luminex does not 78
- Analysis while the Luminex 78
- System is performing data 78
- PN 89-00002-00-254 Rev. B 69 79
- PN 89-00002-00-254 Rev. B 71 81
- Enable Automatic 83
- Analysis 83
- Validating or 85
- Invalidating 85
- Standards and 85
- Running Reports and 87
- Analyses 87
- PN 89-00002-00-254 Rev. B 79 89
- Print Data 90
- Analysis Report 90
- Database Management 91
- Procedures 91
- To drain the system: 94
- Run Self 94
- Diagnostics 94
- To run self diagnostics: 94
- To perform a disk cleanup: 95
- Using the Cleanup 95
- Daily Shutdown 96
- PN 89-00002-00-254 Rev. B 87 97
- Glossary 99
- PN 89-00002-00-254 Rev. B 91 101
- Output.CSV 103
- Field Definitions 104
- Statistic Description 106
- Statistics Column 107
- Definitions 107
- Column Name Description 108
- Index-2 116
Produits connexes et manuels pour Équipement Luminex IS Version 2.3 (IVD)
(10 pages)
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.728 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels