Luminex xPONENT 4.0 SP1 Manuel d'utilisateur Page 130
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Luminex xPONENT 4.O Software Manual
118
Invalidate Standards and Controls
Your xPONENT system administrator must give you privileges to invalidate standards if
you are using the Secure xPONENT package. You can invalidate or remove a standard if
doing so improves the curve fit.
CAUTION: Observe caution when invalidating standards. Doing so greatly
affects the curve fit and subsequent sample results.
For further instruction on assay standard curves and the appropriateness of invalidating or
removing standards, contact the assay kit manufacturer.
It is possible to invalidate or remove a control in data analysis. However, Luminex does
not recommend invalidating controls. For information on assay controls and guidelines
regarding accepting or rejecting control values, contact the assay kit manufacturer.
Your system administrator must give you privileges to invalidate standards.
1. Open the Results page, then open the Saved Batches tab.
2. Open the Saved Batches tab.
3. Click the batch name, then click Open. The Results tab opens.
4. Click the square area next to left of the standard you wish to invalidate, then click
Invalidate. The whole row turns red.
View Batch Settings
1. Open the Results page, then open the Saved Batches tab.
2. Click Saved Batches, then click the batch for which you want to view details.
3. Click Open, then click the Settings tab.
4. Click the left and right Page arrows to view the pages of the batch settings report.
5. Click Save to open the Save As dialog box. Navigate to the location you wish to save
the batch settings report, and click Save.
View Batch Logs
1. Open the Results page, then open the Saved Batches tab.
2. Click Saved Batches, then click the batch for which you want to view details.
3. Click Open. The Results tab opens.
4. Click Log to open the Log tab.
View Sample Details
1. Open the Results page., then open the Saved Batches tab.
2. Click Saved Batches, then click the batch for which you want to view details.
3. Click Open, then click Sample Details. The Sample Details tab opens. If you are
using an LIS licensed package of the software, click Transmit to transmit sample
details to the LIS database. You can transmit either a single analyte per sample or the
entire sample.
- xPONENT 1
- 4.0 SP1™ 1
- Software Manual 1
- Software 5
- Table of Contents 9
- Contents 11
- Introduction 13
- About This Guide 14
- Warnings, Notes and Symbols 14
- General Guidelines 15
- Bead Concentration 16
- Sample Volume 17
- Sample Dilution 17
- Reagents 18
- Touring the Software 19
- Help Icons 20
- Screen Elements 21
- System Monitor 22
- Home Page 24
- Samples Tab 26
- Create Sample Tab 27
- Batches Tab 28
- Batch Plate Layout Report 29
- Protocol Tab 30
- Stds & Ctrls Tab 31
- Plate Layout Tab 33
- Save Protocol Dialog Box 35
- Settings Tab 36
- Logistic 5P. Type the 38
- Analytes Tab 39
- Analysis Settings Dialog Box 40
- Create a New MultiBatch 45
- • Print. Prints report 47
- • Save. Saves report 47
- Multibatch Report dialog box 48
- Current Batch Tab 49
- Saved Batches Tab 55
- Filter Setup Dialog Box 56
- Select Replay Mode Dialog Box 58
- Results Tab 60
- • Message 62
- Sample Details Tab 63
- Reports Tab 64
- LIS Results Tab 64
- Analytes Tab 71
- Std/Ctrl Details Tab 79
- Maintenance 80
- Auto Maint Tab 81
- Lot Management Tab 82
- Cmds & Routines Tab 83
- Probe and Heater Tab 87
- System Info Tab 89
- System Status Tab 91
- Support Utility Tab 92
- System Setup Tab 94
- LIS Settings 95
- • #p - Protocol name 96
- • #b - Batch name 96
- • #u - Logged in user name 96
- Group Setup Tab 97
- User Setup Tab 100
- Create User Account Screen 101
- Batch Options Tab 103
- Alert Options Tab 105
- Setup Email Dialog Box 106
- CSV Options Tab 107
- Cancel - Cancels changes 108
- Save - Saves changes 108
- Archive Tab 109
- Licensing Tab 110
- Schedule Tab 111
- Report Options Tab 112
- Using the Software 113
- System Setup 114
- Data Conversion 115
- Group Setup 116
- User Setup 116
- Batch Options 117
- Alert Options 117
- CSV Options 118
- Licensing 119
- Schedule 119
- Report Options 119
- Adjusting the Sample Probe 120
- System Initialization 120
- Run System Initialization 121
- Add CAL or VER Kits 121
- Managing Sample Lists 122
- Setting Up Batches 123
- Create a Multi-Batch 126
- Import Batch 126
- Export Batch 126
- Performing Analysis 127
- Analyze Current Batch 128
- Manage Saved Batches 128
- Analyze Saved Batch 129
- View Batch Settings 130
- View Batch Logs 130
- View Sample Details 130
- View and Print Reports 131
- Transmit a Batch 131
- Protocols 131
- Import Protocol 136
- Add New Lot for Protocol 136
- Delete Protocol 136
- Export Protocol 136
- Lots and Kits 137
- Performing System Maintenance 138
- Perform System Calibration 139
- Manage Maintenance Routines 139
- Support Utility 140
- Shutting Down the Analyzer 141
- Logging Out of the Software 141
- Exiting the Software 141
- Technical Support 141
- Luminex Website 141
- Glossary 143
Produits connexes et manuels pour Logiciel Luminex xPONENT 4.0 SP1
(192 pages)
(172 pages)
(188 pages)
(184 pages)
(29 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels