Luminex xPONENT for MAGPIX 4.2 Manuel d'utilisateur Page 124
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
• Command Sequence - When you select a routine, the individual commands in the routine
appear in order in the Command Sequence list. The list includes the name of each
command, location, status, and any additional information.
• Report - Opens the Reports tab with Calibration and Verification Reports selected in
the Report: list. Click Generate to view the selected report.
• Import - Displays the Open dialog box to select a routine file to import. Select a file and
click Open to import it.
• Export - Opens the Save As dialog box to specify a file name and location to save a
Routine file.
• Save As - Opens the Save Routine dialog box. Choose a routine name to save the routine
under. After saving, the new routine appears in the Routine Name list. This button only
appears if a routine has been customized or if a new routine has been made.
• Cancel - Cancels changes made to the default location of one of the commands in the
Command Sequence. Click it to cancel those changes. This button only appears if
changes have been made to the command sequence.
• Run - Runs the selected routine or command.
Creating a New Routine
Create maintenance routines to facilitate your startup procedure, shutdown procedure,
troubleshooting, or calibration. Ensure that the maintenance routine you create is consistent
with the Luminex analyzer operations and maintenance requirements. See the MAGPIX
Installation and Hardware User Manual for more information.
To create a new routine:
1. Open the Maintenance page, then open the Cmds & Routines tab.
2. In the Routine Name list, click None.
3. In the Plate Name list, select the plate that you will use for the new routine.
4. In the Commands section, click one or more commands to add to the routine. These
commands display in the plate image and in the Command Sequence list.
NOTE: When you choose the CAL command, a Rinse command is
performed prior to the CAL. When the CAL is complete, two
additional Rinse commands are performed. This prevents a bubble
from loading into the chamber. Verify that you have sufficient room in
the reservoir to complete these Rinse commands.
When you choose the VER command, a Rinse command is
performed prior to the VER. When the VER is complete, an
additional Rinse command is performed. This prevents a bubble
from loading into the chamber. Verify that you have sufficient room in
the reservoir to complete these Rinse commands.
5. To change a location (well or reservoir) for a command, click the command in the
Command Sequence list, then click the new location in the plate image.
NOTE: If you attempt to place two or more incompatible commands in the
same well, a message displays instructing you to change the location
of the command. Some commands can be run from the same
location, for example, multiple washes can be run from the reservoir.
Maintenance Page
111
- Software User Manual 1
- Software 3
- 1. Acceptance 6
- 2. Warranties 6
- 5. Patent Disclaimer 9
- Table of Contents 10
- Chapter 1: Introduction 14
- Screen Elements 16
- System Monitor 17
- 11. Power Off button 18
- Quick Start 19
- Basic Procedures 20
- Adding a New License Key 21
- Logging On to xPONENT 21
- Initial Startup 22
- Revive After Storage Routine 24
- Daily Activities 26
- Shutting Down the Analyzer 26
- Logging Off and Exiting 27
- Using Online Help 27
- Luminex Support 28
- Software Packages 28
- MAGPIX Technology 29
- Running Assays with MAGPIX 30
- Biological Samples 31
- Bead (Microsphere) Handling 31
- Fluidics 1 and Fluidics 2 32
- Sample Volume 32
- Examples 33
- Introduction 34
- Chapter 2: Samples Page 36
- Creating a New Sample List 38
- Editing a Sample List 40
- Chapter 3: Batches Page 42
- Setting Up Batches 43
- Using the Batches Page 43
- Protocol Subtab 44
- Batches Page 46
- Create a New Multi-Batch 63
- Batch Procedures 65
- Exporting a Batch 66
- Editing a Batch 66
- Deleting a Batch 67
- Chapter 4: Results Page 68
- Performing Analysis 69
- Current Batch Tab 70
- Saved Batches Tab 74
- Replaying a Batch 78
- Results Subtab 79
- Log Subtab 84
- Sample Details Subtab 85
- LIS Results Tab 86
- Reports Tab 88
- Generating a Report 89
- Chapter 5: Protocols Page 90
- Protocol Procedures 91
- Deleting a Protocol 96
- Editing a Protocol 96
- Lots and Kits Procedures 97
- Editing a Lot 98
- Deleting a Lot 98
- Exporting a Lot 98
- Importing a Lot 98
- Creating a Kit 98
- Protocols Tab 99
- Settings Subtab 100
- Plate Layout Subtab 103
- Analytes Subtab 107
- Protocols Page 108
- Analysis Settings Dialog Box 109
- Chapter 6: Maintenance Page 116
- System Initialization 118
- Lot Management Tab 119
- Importing CAL or VER Kits 120
- Creating a New Routine 124
- Editing a Routine 125
- Deleting a Routine 125
- Running a Routine 125
- Probe and Heater Tab 126
- System Info Tab 130
- System Status Tab 131
- Schedule Tab 132
- Support Utility Tab 133
- Sending a Support.zip File 134
- Chapter 7: Admin Page 136
- Application Settings 137
- LIS Settings 137
- Arrange Main Page Headers 138
- Maintenance Options 138
- Editing an Analysis Program 139
- Removing an Analysis Program 139
- Group Setup Tab 141
- User Setup Tab 144
- Editing User Permissions 145
- Restoring Account Status 145
- Create User Account Window 145
- Edit User Account Window 146
- Batch Options Tab 148
- Alert Options Tab 151
- CSV Options Tab 153
- CSV and Batch Export Options 154
- Archive Options Tab 155
- Performing a Manual Archive 158
- Licensing Tab 159
- Report Options Tab 162
Produits connexes et manuels pour Logiciel Luminex xPONENT for MAGPIX 4.2
(140 pages)
Logiciel Luminex xPONENT Manuel d'utilisateur
(148 pages)
(148 pages)
Logiciel Luminex xPONENT Manuel d'utilisateur
(152 pages)
(152 pages)
(190 pages)
Logiciel Luminex xPONENT Manuel d'utilisateur
(148 pages)
(148 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels